Thursday, June 4, 2009

On Engines



In response to one of Rocky's messages I mentioned a number of things
that can effect compression ratio. Sunday I go to check the mail and
there's this buncha guys peering in my window all saying pretty much the
same thing:

I don't see how ... (you fill in the blank) can have any effect on CR.

A minor variation on the theme was:

(Your favorite expert's name goes here)... sez to do it like ( whatever)
and never mentions (...various unmentionables...).

Please accept the following as a general answer for all.

CRANKCASE

The four holes in the crankcase that accept the cylinder barrels are called
spigot bores. The area around each bore is called the deck and serves to
support the cylinder. The deck of the spigot bores must all be the same
distance from the center-line of the crankshaft. This is something you
check before you start building any VW engine even when using a new
crankcase because sometimes the axis of the crankshaft is machined
slightly eccentric, meaning the main bearing bores are a little bit deeper in
one half of the crankcase than the other. Or more rarely, machined at a
slight angle, with the clutch-end being more to the left, the pulley-end to
the right (or visa-versa). Not often but it happens. So you check it.

With any USED crankcase the spigot bore decks will have been re-faced
-- re-machined to get rid of the shuffle marks. Good shops with the right
equipment always machine the case decks to match but if you buy a used
crankcase from a shade-tree mechanic or a shop that caters to the kiddie
trade you're liable to find almost anything. I've seen cases with as much
as sixty thou variation in the spigot deck height from one side to the
other... and almost that much on the same side of some cases, which tells
you the case came from a drill-press operation (ie, a shop that doesn't
have a milling machine).

Your jugs sit on the deck around the spigot bores. If there is any
difference in their height it will be reflected in the height of the cylinders.
And since the con-rod extension is relative to the center-line of the
crankcase, any variation in the height of the cylinders will show up as a
difference in the deck-height of the piston at TDC.

If that's not clear, make a drawing and work it out but the message here
is that you have to KNOW. You can't guess. You need to blueprint the
case and record your findings, whatever they are, because you're about to
build on that foundation and by the time you get out to the heads you will
have stacked up half a dozen components and even the smallest
variations will have become significant because of the stack-up.

Major point here is that there is always some amount of variation. With
an army of inspectors to insure the quality of every step in the
manufacturing process, for original Volkswagen parts the variations
would tend to cancel each other out rather than stack up. That's not true
with after-market parts. The only way to know what you have is to
measure what you got. Some guys call this 'blueprinting' and make a big
deal out of it but it's mostly common sense.

CRANKSHAFT

Set the crank up in vee blocks or with fitted bearings in a known-true
case half and check the length of the throws, even if it's a good crank
you've just sent out for a polish. Sometimes the grinder will have a bad
day and you'll end up with a crank having a slightly different stroke on
one (or more!) of the journals. So you check it to within the accuracy of
your tooling and record the results. Usually, cranks are pretty good.
Some of those cranks coming in from China are as good as any I've seen.
But some are trash. Ditto for a LOT of welded strokers aimed at the
Kiddie Trade, with examples of every problem you can name being
woefully common. You have to check and record what you find even
when any variation falls within acceptable limits because that variation,
whatever it is, will add to or subtract from the finished dimensions of the
engine.

CONNECTING RODS

To 'rebuild' a rod you re-bush the little end, hone the bush to spec then
pull apart the big end, use a surface grinder to remove a little metal from
the parting line, torque it back together and machine the big-end back to
a true circle relative to the little end. That is, you try to keep the distance
between the center of the big end to the center of the little end the same
as for a new rod fresh from the factory.

Sunnen honer properly maintained, skilled machinist... you can produce a
pretty good rod. Shops that cater to the kiddie trade... wetback labor...
worn-out or poorly maintained machine tools... Forget about it.

So what's the spec for a stock length rod? I donno... 137mm?
Something like that.

Doesn't really matter. (!!) What matters is that all four of your rods
must be of IDENTICAL length. That's what matters. Long or short,
you can deal with that but only if they are all the SAME.

But they won't be. There will be some variation in their center-to-center
length, center of mass and over-all mass. You'll take care of the weigh
differences during balancing but right now you need to know the
variation in their center-to-center length, which is pretty easy to measure
even with simple tools if you use one journal of a crankcase as your
center on the big end and a well fitted wrist pin on the other.

Con-rods are numbered. Use their number in your records when you
record the difference in their lengths. SOP is to identify the shortest rod
then simply record the differences of the other three. Good rods, you'll
be working in tenths.

What's a well fitted wrist pin? Oiled and at room temperature, you
should be able to slide the pin into the little-end with your hands. Once
in, it should fit well enough so that the pin takes at least two or three
seconds to slide OUT when the rod is held horizontally (and the pin is
installed flush). Slower is better. At running temps the forged mild steel
rod will expand more than the polished cast iron pin so a good fit is one
that is damned tight at room temperature. There should never be a
problem with the fit between the pin and the piston because the
coefficient of thermal expansion for aluminum is MUCH greater than for
cast iron; at operating temps the piston will always be an easy fit on the
pin even if they are locked together at room temperature. (You generally
heat the pistons to install/remove the pin.)

A lot of rods aimed at the kiddie trade or used by lo-buck rebuilders
aren't even overhauled. They just knurl the bushing and hone it back to
size and merely hit the big-end with a hammer before honing if they
bother to hone it at all. Shop by price, you'll end up buying junk. Good
shops are proud of the quality of their work, offer no objection if you
want to mike a part now & then. Ditto for good dealers. The other kind
don't want anything to do with real mechanics. And get their wish :-)

PISTONS & CYLINDERS

Pistons & cylinders are manufactured individually then sorted according
to their finished diameter (for jugs) and weight (for pistons). The
different sizes and weights are identified by dots of colored paint on the
pistons.

In manufacturing a cylinder barrel the raw casting is first machined then
the machined barrel is honed to remove the tool marks. In the process of
machining a given number of cylinders, the finished bore will become
gradually smaller as the tool-bit wears down. When it gets to a certain
minimum size they stop the machine and set it back up with a new boring
tool. The point here is that the inside diameter of the jugs being
produced will fall across a certain range of diameters. This is normal.

The honed jugs are measured and divided into groups according to some
standard deviation in their diameter, typically about a thousandth of an
inch. But even with that small a standard, with four jugs from the same
size-group you can expect to find a variation in their diameter. It won't
be much but you need check it.

Volkswagen used cast aluminum pistons from permanent molds. The
density of cast aluminum varies slightly according to how much metal is
in the smelting pot, its temperature and how long its been there. The
castings are then machined to a given diameter, for the grooves where
piston rings, for the wrist pin and for the top of the piston. All other
surfaces are usually left as-cast. As with all machining operations, the
finished dimensions will fall across a range of sizes.

The combination of differing density in the aluminum alloy and variations
in the as-cast dimensions causes VW pistons to vary in weight by as
much as an ounce (!) Even by 1930's standards that's a bit much so the
pistons get sorted into three weight groups with each group having a
maximum variation of ten grams.

The nominal dimension of the piston (i.e., its size group) is stamped on
the top and a dot of colored paint is used to indicate which direction its
actual dimension deviates from the stamped figure. A dot of colored
paint is used to indicate the piston's weight group and a plus or minus
symbol is stamped into the top of the piston to indicate if the piston's
weight is above or below the nominal weight for that group.

The pistons are divided into groups according to their weight and within
each weight group, are divided into groups according to their diameter,
allowing them to be matched with suitable jugs, fitted with rings and
packaged for shipment. Stock jugs used to be available individually;
nowadays all you'll see are sets of four.

But your carton of new pistons & cylinders may arrive as a grossly mis-
matched set of junk. Here's why: Some after-market retails -- or the
clerks who work for them -- tear open the boxes and shuffle sets around
to make up sets having the largest bore diameter and identical weight
markings. Some dealers even brag about this in their advertising,
referring to such sets as the 'pick of the litter' that need no further
balancing. And sell such sets at inflated prices.

It's all bullshit of course. With a weight group encompassing ten grams,
with two divisions and a mark for high or low the best you can hope for
is a spread of 2.5g... about 25x worse than a real balancing job. (Using
an inexpensive electronic scale for measuring and a Dremel tool for
removing metal, the average novice has no trouble matching four pistons
to within a gram or two.)

But the most interesting point of all this is what happens AFTER those
sets of pistons have been pawed over by the clerks. They get tossed back
into the boxes willy-nilly and sold to unsuspecting suckers, including
other retailers.

The tricky bit here is that you can't balance a set of pistons if they span
TWO weight groups. Pistons are provided with extra metal in the form
of 'balancing pads,' areas from which you may remove metal without
effecting the strength of the piston. But the maximum amount you can
remove is only a few grams. That isn't a problem when all of the pistons
are from the same weight group. But with MIXED weight groups you're
liable to see as much as 20 GRAMS difference across your four brand
new jugs. Not only does that violate the factory spec of 10g, the
difference is too large to be balanced out - - there simply isn't enough
metal that can be safely removed.

You just paid good money for a set of new jugs that are junk.

But this is about compression ratio so let's get back to that.

First thing you gotta do is examine your new set of P&C's to make sure
they are of the same size group (ie, the variation of diameter) and within
the same weight group. That is, all four of the jugs in the box should
have the same color code for dimension and the same color basic color
code for weight group. The code for plus & minus doesn't matter
because you're going to have them re-balanced to a finer standard of
precision (i.e., typically +/- 0.1g across a set of 4).

You should do all that before you buy them. And yes, you can get
royally screwed when buying through the mail. No, I won't recommend
anyone -- I've been sued both ways on that one, once because a guy was
unhappy with someone I recommended and another time by a dealer
because I DIDN'T recommend him. So go fish. And good luck.
Because getting a set of P&C's that hasn't been tampered with is just the
start of the story.

Once you have a set of P&C you'll need to put identifying marks on the
jugs and record the marks and the dimensions in your notes. I file
notches in the flat area of the upper-most fin. When you have more than
one engine in the shop at a time, keeping their parts separate can be a
problem. I use a series of adjoining notches to identify the set then one
to four additional notches, spaced apart, to identify a particular jug within
a set. The notches are cut with die-grinder as soon as I open the box.
The pistons have to stay with their particular jug so you need to put a
matching mark or number on the underside of that piston. I use a
vibrating scriber.

Begin your measurements with the distance between the deck lip and the
top of the cylinder barrel. The easy way to do this is to just stand the
thing on its head and use a surface gauge to find the tallest barrel then
record any difference in the other three. Here again, you can expect
some small variation.

Barrel length is an especially critical dimension in an horizontally
opposed engine since it is the foundation of the valve train geometry.
This dimension is even more important in horizontally opposed engines
like the Volkswagen which depend upon head studs (or stays) to
maintain the seal between the cylinder and the head since any difference
in the length of the barrels will impose an asymmetric load on the sealing
surface leading to compression leaks.

After measuring the length of the barrels the pistons are removed and the
pin height is measured. Follow the same general procedure; put the
piston, head down, on a surface plate, use a gauge to find the tallest then
record the difference between it and the other. (As a point of interest, in
most cases there's nothing to record - - the dimensions match to within
less than a thousandth of an inch and an amount that small is generally
not significant. What I'm really looking for here is any radical departure
from the norm.)

The rings get removed and a lot of other work gets done but we're only
talking CR here so I won't go into the other stuff.

CYLINDER HEADS

As with the jugs, when measuring the heads you must first identify them.
Through the course of assembling an engine the heads get a lot of work
done to them and you need to keep good records. I stamp numbers on
them, over by the right-hand exhaust stack (right-hand looking into the
chambers, push-rods down). Doesn't really matter how you identify them
just so you do. I use stamped numbers because in prepping a set of
heads I usually replace some of the guides, run them through the blasting
cabinet to roughen up certain areas then open up the chambers, unshroud
the valves and do a few other things, most of which will destroy any kind
of temporary markings.

On the chamber-side of the head casting you will find either a fully
machined flat area surrounding the chambers (old style heads) or six
machined bosses, three to each chamber. The horizontal plane defined by
the machined surface is the base-line for all of your head dimensions.

You need to know the distance from that horizontal plane to the sealing
surface of the combustion chamber. More specifically, you want that
distance to be as close to identical as possible for both heads and, within
a head, for both chambers.

This dimension can be all over the map if the heads have been opened up
by a schlock shop. Good shop, any variation should only be a few tenths
(ie, ten-thousandths of an inch) up to a max of half a thou (ie, fifty
ten-thousandths). Shlock shop, using a cutter in a drill press, you won't
believe the crap they turn out.

This dimension is especially critical in the fabrication of a good VW
engine. If this distance varies by more than two thou between the
chambers of the same head, or by five thou between a pair of heads,
have the heads fly-cut by the minimum amount needed to arrive at a
uniform figure for all four chambers.

With measurements for the case deck height, barrel length, rod length
and piston head height, and knowing the compression ratio you are
planning to use, measuring your chamber volumes tells you how much
you will have to open them up to achieve the desired compression ratio.
Indeed, once you've nailed down a few dimensions, setting up the correct
compression ratio becomes something of a no-brainer.

And somewhere about now you'll realize this message wasn't about
compression ratio at all :-)

- - - - - - - - - - - - - - - - - - - -

There are two main reasons for doing the work described above. The
first is to be able to identify good parts from bad parts. You can't make
this determination by price nor the fact the part is new, rebuilt or
whatever. Nowadays there is so much junk out there the wiser course is
to assume you're dealing with shoddy goods until its specs prove
otherwise.

As you progress through the measurement of the parts you begin to see
ways in which you can combine those parts so as to arrive at the most
dimensionally-uniform result. For example, a slightly short throw on the
crank can be combined with a slightly long rod. The same is true for the
jugs and the heads in that some combinations may be used to cancel out
dimensional variations.

A nice point to keep in mind here is that the 'assembly' of a 'paper'
engine is an arm-chair activity. You may take as long you wish, shuffling
the numbers about in every possible combination until you arrive the one
that makes the best possible use of that particular set of parts.

OF THAT PARTICULAR SET OF PARTS...

Did the light-bulb come on over your head? You see, the typical engine-
builder can only afford ONE set of parts. And as much as I hate to say it,
if you simply bolt them together the odds of getting a good engine are
vanishingly small. Oh, it'll run. Veedubs are robust little buggers...
ANYTHING will run. But if you simply throw the thing together it will
not run as well as it should nor last as long as it could. And you won't
know the difference.

But I'm not a machinist... (I heard someone shout).

Neither was W. Edwards Deming. He was a statistician with the Bureau
of the Census. (Never heard of him? Your loss.)

The truth is, you don't need to be a machinist to build a better engine.
You can do that by simply taking a few measurements and keeping good
notes. That's enough to keep you from building a total piece of shit.
When you subtract the POS Probability Factor from the engine building
equation you AUTOMATICALLY end up with a better engine. How
much better? On average, about twice as good. Yeah, I know... nobody
else believes it either. Except for the guys who have done it. (Didja read
my article on dialing in your cam? Ditto.)

Up to you. It's your engine.

-R.S.Hoover

2 comments:

Royski said...

Thank you very much for sharing your expertise.

Anonymous said...

I am also greatfull for all your work. I am a VW nut and building my own engine for my 75 Westy. I was wondering if you could add a piece on how to correctly heat treat paint. Thank you very much.